RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: 757jonp
Showing results 1 to 16 of 16
Search took 0.01 seconds.
Forum: Gas Engines
12-11-2020, 05:50 PM
Replies: 640
Views: 253,003
Posted By 757jonp

Just my opinion.... looks like one of the slave...

Just my opinion.... looks like one of the slave rod clips came loose which allowed the pin to drift back into contact with the balance weight and boom! (see the mark on the balance weight) Trash...
Forum: Gas Engines
02-18-2020, 05:32 AM
Replies: 640
Views: 253,003
Posted By 757jonp

Kinda interesting that Horizon couldn't (or...

Kinda interesting that Horizon couldn't (or wouldn't?) tell you what the factory timing was set at. I found both my FG60 and FG90 at 45 deg BTDC. I've modified both of mine to reset the timing @...
Forum: Gas Engines
02-17-2020, 04:00 PM
Replies: 640
Views: 253,003
Posted By 757jonp

I'm not a big fan of using a LiPo battery of any...

I'm not a big fan of using a LiPo battery of any kind of "fuel" powered aircraft. To much hassle removing.reinstalling for charging/possible fire danger, etc.
Forum: Gas Engines
02-16-2020, 06:11 PM
Replies: 640
Views: 253,003
Posted By 757jonp

I personally use A123 2100 @ 6.6 volts from...

I personally use A123 2100 @ 6.6 volts from Hangtime Hobbies, but really it's up to you. Anything in the 1000 and up Ma range up to 9 volts will work. (so says the instructions)
Forum: Gas Engines
02-15-2020, 09:19 AM
Replies: 640
Views: 253,003
Posted By 757jonp

alvarog... That doesn't sound good. Perhaps...

alvarog... That doesn't sound good. Perhaps it's time to get hold of Horizon (or whoever you bought it from) and see if there's a warranty issue to pursue. If not, perhaps CH Ignition would be...
Forum: Gas Engines
01-04-2020, 04:34 PM
Replies: 640
Views: 253,003
Posted By 757jonp

I stand corrected on the exhaust nipple size. It...

I stand corrected on the exhaust nipple size. It is 15MM vs 14MM. I've got an appointment with the eye doc next week!
Forum: Gas Engines
12-30-2019, 04:22 PM
Replies: 640
Views: 253,003
Posted By 757jonp

It's 14mm. Same as a 120, 150, and 180 Saito...

It's 14mm. Same as a 120, 150, and 180 Saito single.
Forum: Gas Engines
11-28-2019, 10:55 AM
Replies: 640
Views: 253,003
Posted By 757jonp

I just use a hand held unit..... Happy...

I just use a hand held unit.....

Happy Thanksgivng everyone!
Forum: Gas Engines
11-28-2019, 08:43 AM
Replies: 640
Views: 253,003
Posted By 757jonp

I'm sorry, but I don't have a pic of it and the...

I'm sorry, but I don't have a pic of it and the plane is in storage right now. It's pretty simple. I used a piece of pushrod with a 90 deg bend guided by a brass tube epoxied to the firewall. ...
Forum: Gas Engines
11-26-2019, 04:24 PM
Replies: 640
Views: 253,003
Posted By 757jonp

I call it more of an "primer" than a choke. ...

I call it more of an "primer" than a choke. Actually what it does is slide the barrel and needle clear of the fuel inlet allowing raw fuel to be drawn/pumped into the carb throat. Works great.. I...
Forum: Gas Engines
11-21-2019, 07:44 PM
Replies: 640
Views: 253,003
Posted By 757jonp

Hey Enjoyav8ation...wondering when you'd make it...

Hey Enjoyav8ation...wondering when you'd make it over here. Kinda strange deal you got there with the L/S needle. IDK how many turns total I have on mine, but it's a heckuva lot more than 4.25...
Forum: Gas Engines
11-21-2019, 05:14 PM
Replies: 640
Views: 253,003
Posted By 757jonp

Yes.. I'm very familiar with Ray English and his...

Yes.. I'm very familiar with Ray English and his mods to the Saito radials as well as Mr Morris in England The ignition timing problem was originally seen by Morris and his mod also compensates...
Forum: Gas Engines
11-20-2019, 01:54 PM
Replies: 640
Views: 253,003
Posted By 757jonp

On the 60 I didn't use anything as it fits pretty...

On the 60 I didn't use anything as it fits pretty close. The 90 in the Texan is a little looser, but I haven't done anything to to it yet, but I might put some short ply baffles in the cowl before...
Forum: Gas Engines
11-20-2019, 10:55 AM
Replies: 640
Views: 253,003
Posted By 757jonp

I don't see any reason why you couldn't do that,...

I don't see any reason why you couldn't do that, but an easier way might be to build a ply box similar to what I did and use a self tapping screw to fasten it between the fins of the heatsink? Build...
Forum: Gas Engines
11-19-2019, 06:59 PM
Replies: 640
Views: 253,003
Posted By 757jonp

Hey jimkron... I think you'll find most full...

Hey jimkron... I think you'll find most full scale air cooled engines have the "tins" (baffles) attached to the engine, but there may be some attached to the cowl too. I like doing it this way...
Forum: Gas Engines
11-18-2019, 05:18 PM
Replies: 640
Views: 253,003
Posted By 757jonp

I haven't seen much activity of this thread...

I haven't seen much activity of this thread lately, but I wanted to share a alternative method of installing baffles on the FG-90 that I came up with. I bought and mounted this engine on a Ziroli...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.